Laser Engravable Rubber - Extra Thick

: $24.00

Item Number: LR-ET

Quantity:

Add to a new shopping list

Email this page to a friend

Quantity Discounts - Order a quantity of this item to receive the lower price

Quantity	Amount
2 to 4	$21.36
5 to 24	$20.16
25 to 49	$18.72
50 to 99	$16.80
100 to 1000	$15.36

This gray pre-vulcanized Laser Rubber is approximately .120” or 1/8” thick. A4 sheet size (about 8¼” x 11¾”). Clean burning leaving a white ash residue. In production it has an odor that may be offensive to some people.

Must be washed with detergent and water after engraving. Confirm that your laser equipment is suitable for engraving stamp dies. Check with your laser equipment manufacturer to determine compatability of equipment and software.

The settings below are a good starting point as you begin test engraving this material. Use your laser’s software settings for “stamp” mode or “3D effects” mode. Adjust speed and power settings as needed. Use your machine’s air assist mode while engraving. Observe the following precautions:

• Laser engraving or cutting rubber can possibly ignite the material. Never leave the laser system running unattended for any reason.
• Laser engraving or cutting rubber can produce foul odors. You may need to particulate filter or odor filter your exhaust depending on your environment, installation location and local air quality control regulations.
• Laser engraving or cutting rubber can produce abrasive dust and smoke. You will need to clean your laser more frequently to reduce wear and tear and keep the optics clear.
• Laser Rubber can be engraved on either side.
• When vector cutting this material be sure to use a vented cutting table. Without a cutting table the likelihood of flame increases.
• After engraving, wash the material with detergent and water. Then rinse and towel dry.

Suggested Laser Rubber Engraving Parameters

Related Products

Laser Engravable Rubber & Polymer : From $14.80 to $26.00 Stamp Die Products for Laser Engraving!	Acrylic Clear Stamp Mounts : From $0.39 to $74.00 Virtually Any Size!
Laser Engravable Rubber by the Roll : From $66.00 to $539.00 Stamp Die Products for Laser Engraving!	IDEAL/Trodat Self-Inking Stamps : From $5.50 to $16.00 The Most Popular Self-Inking Stamps Worldwide!
Art Stamp Wood Mount Strips : From $4.40 to $15.60 Beautifully Sanded Hardwood Mounts	Coverdex Wood Mount Strips : From $5.90 to $30.40 Traditional Style Stamp Mount Block
Art Stamp Wood Mounts, Pre-Cut : From $0.66 to $7.10 Pre-Cut to Virtually Any Size!	Plastic Rubber Stamp Handles : From $1.15 to $1.30 Low Cost Combined with Ergonomic Design
Wood Rubber Stamp Handles : From $1.98 to $4.30 Four Sizes and Two Colors for Every Application	E-Z Indexing Sheets : From $12.08 to $74.75 Print and Attach to Your Artstamp Wood or Acrylic Mounts
Indexing Ink : From $8.85 to $344.00 For Stamping on Top of the Mount	Self-Adhesive & Plain Sponge Cushion : From $9.80 to $34.00 For Mounting Stamp Dies to the Mount
Paper Based Phenolic : From $3.70 to $26.00 For use with Rotary Engraving Equipment	Rubber Cement : From $10.80 to $133.00 For Mounting Rubber Dies
Cutting Shears : $48.00 Ideal for cutting rubber or polymer dies.	Gray Cling Cushion & Static Cling Film : From $1.15 to $399.00 Stamp Dies Can be Mounted Almost Anywhere!